Low Barrier
Dual-Wire Wrist Straps

MagSnap 360™

2229 - MagSnap 360™ Metal Wrist Strap Kit - Medium band with 6' Coil Cord

  • 360° Rotation Between Wristband and Coil Cord
  • Magnetic Connection Between Wrist Band and Coil Cord
  • Dual-Wire Metal Expansion Wristband and Coil Cord

Foot Grounders

HGS1MD-RED - Heel Grounder, Standard, 15′, D-Ring, Red Elastic

This grounder features a D-Ring Strap and elastic hook and loop for adjustability. Compliance verification is simplified by the bright red elastic strap. Heel Grounders are designed and manufactured for comfort, durability and cost effectiveness.

Dual Wire Smock Jacket

Dual-Wire Smocks

770100 - Dual-Wire Smock Jacket with Knitted Cuffs

  • Groundable Static Control Garment System Meets ANSI/ESD S20.20 (Rtg <3.5 x 107 ohms)
  • Panel-To-Panel Conductivity
  • Hip-To-Cuff Grounding
Dual Wire Smock Jacket in use

WS Aware Monitor

770067 - WS Aware Dual-Wire Monitor with Standard Remotes and Ethernet Output

  • SCS 770069 Power Relay Compatibility
  • Dual Workstation Continuous Monitor
  • Ethernet Connectivity
  • Digital Signal Processing Technology
Combo Tester

Dual Combination Tester

770758 - Dual Combination Tester

  • Compatible with Single-Wire and Dual-Wire Wrist Straps
  • Simultaneous Testing of Wrist Strap and Footwear in Less Than 3 Seconds
  • Solid-State Test Switch with No Moving Parts
  • Split Foot Plate for Testing Foot Grounders (or ESD Shoes)
Worksurface Mats

Worksurface Mat

8903 - Mat Roll, 2-layer Rubber, 8900 Series, Blue, 0.065″x30″x50′

  • Dissipative Dual Layer Rubber Material
  • 2-Layer Neoprene Layer Rubber Material
  • High Strength Vulcanized Synthetic Neoprene Rubber Heat and Chemical Resistant
Charge-Guard Wipes

Charge-Guard™ Wipes

8004 - Charge-Guard™ ESD Surface and Mat Cleaner, 25 Wipes

  • Ideal for Use After Sanitizing
  • Packages in Dri-Shield® 2000 moisture barrier pouch - Removes dust, grease, grime, fingerprints, solder flux and other contaminants from ESD mats and other surfaces
  • Alcohol-Free Formula - Excessive use of alcohol-based cleaners may dry-out mats (vinyl or rubber) and degrade performance

Grounding Hardware

770115 - Ground Cord, 10 mm Stud, 15′, No Resistor with Ring Terminal

  • Stud has threaded hole; 6-32x1/4″ flat head screw and countersunk washer are provided
  • Ring terminal at the end of ground cord
  • No resistor included, meets Grounding Standard ANSI/ESD S6.1
Floor mats

Anti-Fatigue Mat

9900 - Anti-Fatigue Rubber Mat, 0.600″ x 3′ x 5′

  • Rtt: < 1 x 106 ohms per ANSI/ESD 7.1 and ESD TR53
  • Low Profile
Static Shielding bag

Static Shielding Bag

10068 - 1000 Series Metal-In Static Shielding Bag, 6″ x 8″, 100 EA

  • Metal-In Film Laminate 0.0028″ thick (2.8 mil)
  • <10 nJ Discharge Shielding Energy Limit Test per ANSI/ESD STM11.31
  • Open Top and Zip Top Styles are Available
Static Shielding Bag in use

Dri-Shield® 2000 Series Moisture Barrier Bag

7001824 - Dri-Shield® 2000 Series Moisture Barrier Bag, 18″ x 24″, 100 EA

  • 0.0036″ (3.6mil) Thick Bag Film laminate constructed from multiple layers of aluminized polyester and polyethylene
  • <\= 0.03 Grams Moisture Vapor Transmission Rate (MVTR)
  • <10 nJ Energy Penetration Tested per ANSI/ESD STM11.31

Humidity Indicator Card

51060HIC125 - Humidity Card, 5-10-60%, 125/Can

  • Measures the level of relative humidity that the contents of the packaging have been exposed to
  • Meets IPC/JEDEC J-STD-033D (Type 1) Table 3-1 Dry Packing Requirements
  • 125 Cards per can
Humidity Indicator Card


1PLDES300 - Desiccant in Tyvek® Pouch, 1 Unit, 300/Pail

  • Provides protection for moisture sensitive electronics
  • Desiccant is secured in strong, sulphur-free non-woven plastic pouches
  • Can be baked and re-used

BenchTop Ionizer

963E - Benchtop Air Ionizer, North America

  • Steady-state DC benchtop ionizer with auto-balance
  • Less than 2 seconds discharge time with ±15 volts offset voltage
  • Electrostatically shielded emitter points
  • No grounding wires required
Benchtop Ionizer
Benchtop Ionizer

Overhead Ionizer

770112 - Ion Pro™ Overhead Ionizer with LED Lighting, 2-Fan, 120VAC

  • Two Fan Steady-State DC Ionization For 2′ x 4′ Coverage Area
  • 3 Seconds or Less Discharge Time with ±10 Volts Offset Voltage (Balance)
  • One 700 Lumen LED Panel Light
  • 3 Position Fan speed: Low, Medium, High

Aisle Marking Tape

AISLETAPE54 - ESD Aisle marking Tape, 3″ x 54′, Roll

  • .006″ Thick (6 mils), scuff resistant
  • Bright Yellow Color
  • 3″ Width, 54′ Length, 3″ Core
Static Shielding Bag in use
Sign and posters

Sign & Posters

ESDSIGN4X10 - ESD Awareness Sign, RS-471, 4″ x 10″

  • 4″ x 10″ ESD Awareness Sign
  • Apply to Doors, Floors, Walls, Tote Boxes, Workbenches
  • Constructed from Laminated Stock
Resistance Pro Meter in use

Resistance Pro Meter

770760 - Resistance Pro Meter Kit

  • Digital Compliance Verification Surface Resistance Meter Kit
  • Resistance Range: 1.0 x 103 to 1.0 x 1012 ohms
  • Large OLED Display, Internal Memory Measurement Stability Modes, and More!
Resistance Pro Meter
Static Sensor

Static Sensor

770716 - Static Sensor

  • Portable Meter for Testing of Electrostatic Fields
  • Chopper-Stabilized Sensor
  • Dissipative Enclosure with 7mm Ground Snap
  • Rotary Zero Knob
Static Sensor in use

EM Eye - ESD Event Meter

CTM048-21 - EM Eye - ESD Event Meter

  • Detects, counts and measures ESD events that can damage ESD items and cause tool lock-ups, erratic behavior and parametric errors
  • Records all measurements to a microSD card for PC download
  • Touchscreen display provides intuitive user interface
  • Rechargeable lithium ion battery
Static Sensor in use
Static Sensor in use


770045 - EOS/ESD Assessment Kit

Kit Includes :

  • 770760 Resistance Pro Meter Kit>
  • 770765 Handheld Electrode
  • CTM048-21 EM Eye - ESD Event Meter
  • CTM051 Ground Pro Meter
  • 770717 Air Ionizer Test Kit
  • ESD Training Paddles Set
For more information on ESD Essentials or setting up an ESD Workstation CLICK HERE and we can set up a virtual call!
Contact Us Virtual Appointment